Difference between revisions of "Signal Joining Rings"
(→Visual Identification Guide) |
|||
| Line 12: | Line 12: | ||
=== Visual Identification Guide === | === Visual Identification Guide === | ||
{| | {| | ||
| − | |[[Image: | + | |[[Image:CarriageRing_RCHDOH.jpg|200px|link=#Round Center, Carriage Only]] |
| + | |[[Image:CarriageRing_RCHSOH.jpg|200px|link=#Round Center, Through-Hole]] | ||
| + | |[[Image:CarriageRing_RCHSOHLG.jpg|200px|link=#]] | ||
|- | |- | ||
| − | |[[Image:CarriageRing_GEStreamline.jpg|200px|link=# | + | |[[Image:CarriageRing_Mickey.jpg|200px|link=#]] |
| + | |[[Image:CarriageRing_MickeyClip.jpg|200px|link=#]] | ||
| + | |[[Image:CarriageRing_MickeySmall.jpg|200px|link=#]] | ||
| + | |[[Image:CarriageRing_Pelco.jpg|200px|link=#]] | ||
| + | |- | ||
| + | |[[Image:CarriageRing_Rad.jpg|200px|link=#]] | ||
| + | |[[Image:CarriageRing_Delta.jpg|200px|link=#]] | ||
| + | |[[Image:CarriageRing_SiemensEuro.jpg|200px|link=#]] | ||
| + | |[[Image:CarriageRing_Poly1.jpg|200px|link=#]] | ||
| + | |- | ||
| + | |[[Image:CarriageRing_GECan1.jpg|200px|link=#]] | ||
| + | |[[Image:CarriageRing_GECan2.jpg|200px|link=#]] | ||
| + | |[[Image:CarriageRing_3MClip.jpg|200px|link=#]] | ||
| + | |[[Image:CarriageRing_GEStreamline.jpg|200px|link=#]] | ||
|} | |} | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
CarriageRing_RCHDOH.jpg | CarriageRing_RCHDOH.jpg | ||
Revision as of 21:43, 5 November 2014
Overview
Signal joining rings are known by different names depending on the signal equipment manufacturer. The most common trade name might be carriage ring or tri-bolt washer. [Insert some other names from various manufacturers.] All of these names and hardware are interchangeable. Brought about during the post WWII advent of modular, closed body signal construction, these are the unified flat washers that, along with typically three carriage bolts, join two traffic signal aspects together via the unused pipe mount bosses. This replaced the much less adaptive, sealed, or repairable design of open body signal sections held together with a single set of endplates and tie-rods. When the modular body sections were keyed for serrated locking rings on both top and bottom of the signal aspect it was also possible to create “twisted” signal designs wherein each lens does not need to point in the same direction, they are free to rotate 360° about the mounting axis.
Exceptions
There were a few notable exceptions to the use of carriage rings in closed body signal construction.
Marbelite
Most notably is the earlier body styles of Marbelite signals. Despite having the typical pipe boss and capable of using a tri-bolt ring the castings were molded with three drill out reliefs near the outer extremities of the signal. To assemble, one drilled these three holes on each signal, stacked them, then bolted them together with a bolt and square washer. While an elegant approach, and one could say more reliable, it was eventually eliminated for the common carriage ring design.
Crouse-Hinds
Another, rarer bird, is the rodded CH Type M (Breadpan.) For city specific requirements, this signal was constructed conventionally (with the tri-bolt washer) but available with each body section drilled and rods inserted through them all creating a belt-and-suspenders approach. This was perhaps less of a Luddite approach than it seemed. The Type-M body design did not have any serrations or other keying features on the top of the signal section, only the bottom. When stacking them, it was only the alignment and tightness of the bolts that would retain a signal aspect from rotation.
Visual Identification Guide
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
CarriageRing_RCHDOH.jpg CarriageRing_RCHSOH.jpg CarriageRing_RCHSOHLG.jpg CarriageRing_Mickey.jpg CarriageRing_MickeyClip.jpg CarriageRing_3MRound.jpg CarriageRing_Poly1.jpg CarriageRing_3MClip.jpg CarriageRing_Delta.jpg CarriageRing_SiemensEuro.jpg CarriageRing_GECan1.jpg CarriageRing_GECan2.jpg CarriageRing_MickeySmall.jpg CarriageRing_Rad.jpg CarriageRing_Pelco.jpg*
