Tokheim

From HighwayWiki
Revision as of 02:01, 1 January 2014 by Larryc39 (talk | contribs)
Jump to: navigation, search

File:TOK-LOGO-LC.jpg


Summary

Following the February 1898 design of a gas pump by John J. Tokheim the Tokheim Manufacturing Company was incorporated in Cedar Rapids, Iowa in 1901. In 1918 employees of the Wayne company set out on their own, purchasing Tokheim and reincorporating it as the Tokheim Oil Tank and Pump Company, moving to Fort Wayne, Indiana in the old Wayne Spoke and Bending Company factory. In April 1926 they acquired the Signaphore company, also located in Fort Wayne, and formed the Tokheim Traffic Signal Division - although such branding has not been seen on their products, instead retaining the TOT&PCo. nomenclature. This acquisition brought along J. N. Paul of Automatic Signal Co. and Ruben E. Bechtold, from Signaphore. They would greatly develop and expand the Signaphore line into the modern traffic signal as well as introduce new controllers. By 1937 their interest in the product line waned and on January 8th, 1938 the transition of their signal interests to Automatic Signal took place, along with pioneering traffic engineer Reuben E. Bechtold.

When the Signaphore line was acquired they were producing novel 4-way traffic signal standards that appeared much like a round bodied gas pump with a traffic light on top. Like many manufacturers of the day they produced signals out of both aluminum and copper, later switching to all aluminum. Quite popular locally, they attracted the attention of Detroit, who requested pole-mount versions of the signal. Adjustable traffic signals would follow, and their market spread throughout the midwest including such cities as Cleveland, Chicago, and Detroit. It has been said they entered the international market too, however little is know of that.[1]


Traffic Signals

All Tokheim signals were designed with several characteristics:

All bodies are of cast aluminum Felt gaskets are used on the lense and door Doors are portholes held in place with two L-clamps and wingnuts All visors were cutaways with 8" length Reflectors are thick glass with an electrolytic copper plating Reflectors are held in a pan and mounted to the signal body Sockets are a porcelain Leviton wing style Wiring is done with rubber wire Lamps are 50-Watt household or 60-Watt traffic bulbs


Tokheim signals also had several options available (Mainly four-way exclusives):

Blank covers on one to three sides 15°, 30°, or 45° angled doors Traffic Bell


Four Ways

Cut 1200 - Four-Way Aerial Traffic Control Signal

TOK-CUT1200-LC.jpg

Figure: Tokheim 1200 Signal. [Image by LC]

Cut 1260 - Four-Way, Two Color, Aerial Traffic Control Signal

No Yellow/Caution Lens


TOK-CUT1260-LC.jpg

Figure: Tokheim 1260 Signal. [Image by LC]


Cut 1300 - Four-Way, Post-Type, Traffic Control Signal

TOK-CUT1300-LC.jpg File:TOK-CUT1300B-LC.jpg

Figure: Tokheim 1300 Signal. [Image by LC]


Sectional Signals

At some time, 4-way sectional heads were also made.


Adjustables

Cut 1310 - One-Way, Post-Type, Traffic Control Signal

Also available in two to five way clusters. Solid Body


TOK-CUT1310-LC.jpg

Figure: Tokheim 1310 Signal. [Image by LC]


Cut 1400 - Horizontal Adjustable Post Bracket, Traffic Control Signal

TOK-CUT1400-LC.jpg

Figure: Tokheim 1400 Signal. [Image by LC]


Cut 1406 - One-Way, Vertical-Bracket Type, Traffic Control Signal

Also available in two to four way clusters. Solid Body


TOK-CUT1406-LC.jpg

Figure: Tokheim 1406 Signal. [Image by LC]


Cut 1410 - Vertical Adjustable Post Bracket, Traffic Control Signal

TOK-CUT1410-LC.jpg

Figure: Tokheim 1410 Signal. [Image by LC]


Sectional Signals

This is a sectional signal head made by Tokheim.


TOK-AdjSection-LC.jpg

Figure: Tokheim sectional head. [Image by LC]

Pedestrian Signals

Tokheim did not manufacture any pedestrian signals.


Informational Signals and Signs

describe models, variations [delete] includes "box signs," "case signs," and Ped Heads with special [non-ped] lenses.


Lenses

Lenses are 8 3/8" dia. with a 90° diffusing pattern. Command lenses are optional, with embossed letters two inches high, and a baked enamel finish.


Controllers

Controllers were individually settable for the Red, Yellow, and Green phases. Stop and Go could be set for anywhere from 15 sec. to 3 minutes. The clearance, yellow, could be set from two seconds to seven[?] seconds.

Cut 2000 - Chronoplan

Not a controller in itself, but the Tokheim guide on installation and setup of a traffic controller system utilizing a Chronolizer and several 1500 Timer modules. Improvements of up to 94% over the synchronized system and 43% over the staggered controller systems were guaranteed for a car doing the speed limit.

Chronolizer - Central Controller

This was a device attached to a series of 1500 timers to control a full roadway of signals in interoperation and coordination.

Cut 1500 - Traffic Signal Timer

Intoduced in 1925, the model 1500 was a local timer for controlling traffic signals.

TOK-CUT1500-LC.jpg

Figure: Tokheim 1500 Signal Timer. [Image by LC]


Cut 1820 - Automatic Traffic Signal Control

The model 1820 was essentially a 1500 timer and associated circuitry in a cabinet to allow isolated operation of a single signal or intersection.


File:TOK-CUT1820-LC.jpg TOK-Controller-LC.jpg

Figure: Tokheim 1820 Signal Controller. [Image by LC]


Magnetic Detector

Part of the later signal line upgrades included early magnetic detectors for vehicle-actuation. Following is an example of the controller with magnetic detection modules and a marketing image of an intersection configured as such.


TOK-MagController-LC.jpg TOK-MagSetup-LC.jpg

Figure: Tokheim magnetic detectors. [Image by LC]

Hardware

this would include any kind of mounting hardware including brackets, slipfitters, hangers, bases, etc. [delete]


Miscellaneous Images

a couple of quality pics of a restored unit [delete]

References

[1] Back to the Future Tokheim, Bob Lee, 1993, ISBN 0-9638220-0-4